50W 2000-6000MHz Drone Jamming Module Blocker RF Power Amplifier GaN Modulefor Anti Drone System WiFi GPS Jammer

Product Description

Product Description

2000-6000MHz 50W RF Power Amplifier Module

The DW-UWB-2-6G-A-50W is a highly reliable amplifier.It employs ultra-wideband GaN transistors that can output 50 watts of power within the 2000MHz to 6000MHz frequency range while maintaining relevant RF performance.In contrast to traditionalCW amplifiers,this amplifier can amplify spread-spectrum signals,with an instant bandwidth of up to 200 MHz. When paired with the appropriate SDR digital excitation source,it can produce excellent interference effects on remote control,data transmission,and positioning signals. Therefore,this amplifier is particularly suitable for use in 
wireless communication interference systems in the L,S and C bands,including but not limited to mobile phones,radiio stations,and drones.

Equipped with multi-layer heat conduction aluminum casing and intelligent monitoring circuit, the module can real-time monitor working temperature, input & output power, standing wave ratio and operating current. Once abnormal parameters are detected, it will trigger automatic power-off protection to safeguard the whole system safety.

With standard 50Ohm input/output impedance and universal industrial interfaces, this amplifier module can be directly embedded into your existing RF equipment without extra impedance matching modification. It is widely adopted in laboratory testing instruments, short-range radar, wireless signal transmission, RF jammer development, satellite communication auxiliary equipment and other industrial projects.

We support technical parameter customization, OEM shell printing and bulk wholesale discount. Click the link below to check detailed datasheet and technical parameters:

1. Ultra-Wide Frequency Coverage
Covers full 2000MHz to 6000MHz (2GHz-6GHz) bandwidth, perfectly matches S-band & C-band frequency requirements, compatible with most wireless RF transmission devices.
2.Stable 50W High Power Output
Adopts advanced GaN chip solution, saturated output power up to 50W continuous wave, stable power gain with low signal distortion, supports both CW continuous work and pulse working mode.
3. Complete Intelligent Protection System
Built-in over-temperature, over-voltage, VSWR mismatch, over-current automatic shutdown protection modules, effectively avoid burnout caused by abnormal operation, greatly extend service life.
4. Integrated Compact Industrial Design
Integrated aluminum alloy housing with excellent heat dissipation structure, standard 50Ω impedance matching, SMA radio frequency interface, reserved serial communication control port for secondary development easily.
5. Wide Industrial Application Scenarios
Ideal for radar system, microwave test equipment, wireless communication base station, RF signal source amplification, electronic countermeasure, lab research and customized RF system integration.

6. RS485 serial interface for monitoring and control

1.Electrical Specifications
Parameter	Min	Typ	Max	Unit	Test Condition
Operating frequency	2000		6000	MHz
Instant bandwidth			200	MHz	Broadband signal,such as OFDMsignal
Output power Psat	40	50		W	CWsignal
Gain small signal	40		58	dB	Measured with VNA in sweptfrequency mode at-20dBm. Input power calibrated/measuredat the amplifierinputport.
Gain flatness small signal	-3		3	dB	Test condition the sameasGain
Gain adjustment range	20			dB	Test condition the sameasGain
InputRFpower range	-10		6	dBm
Gain adjustment step size	0.5			dB	Test condition the sameasGain
Noise figure			20	dB
Input VSWR			1.8		Measured with VNA in sweptfrequency mode at-20dBm. Input power calibrated/measuredat the amplifierinputport.
Spurious		-60		dBc	CW signal at theoutputpowerof100W. Spurious defined asany non-harmonic amplifier outpur. Spuriousmeasured in a1kHz resolution bandwidth,10kHz video bandwidth.Specifications apply at offsets of greater than or equal to±10kHz from theRF carrier. Maximum measurement frequency is8GHz
Harmonics(2nd, 3nd)	-10			dBc	CW signal source atoutputpowerof100W
Operating voltage	24	28	32	V	Note:Output power capabilities andgain will vary withvoltage
Operating current		10	12	A	CW signal source atoutputpowerof100W
PA Enable/Disable time			1	μs	Measurement with of100WCW output.Rise and fall time of amplifieroutput envelope recorded.Rise and fall times at10%-90% of the output power in linearscale.PAEnable/ Disable signal set to10kHzrepetitionrate and 50%dutycycle

2.Alarm and Protection
Parameter	Introductions
Over temperature	When the temperature exceeds 80℃±5℃,the amplifier PIN7 willoutputs +3.3V voltage and the amplifier will automatically shut down; When the temperature drops below 70℃±5℃, the amplifierwill automatically turn on.
Over VSWR	When the output port of the amplifier is openor short,theamplifierPIN7 will outputs +3.3V voltage and the amplifier shutdown,the status willbe locked. The alarm state willbe cleared once pin15transmitsapulsesignal
Over voltage	The amplifier PIN7 will outputs +3.3V voltage and theamplifiershutdown when the voltage exceeds 32V,the status will belocked. The alarm state willbe cleared once pin15transmitsapulsesignal
Over current	The amplifier PIN7 will outputs +3.3V voltage and theamplifiershutdown when the current exceeds14A.,the status will belocked. The alarm state willbe cleared once pin15transmitsapulsesignal

3.Environmental Specifications
Parameter	Min	Typ	Max	Unit
Operating temperature	-40		+60	℃
Storage temperature	-55		+85	℃
RelativeHumidity (non-condensing)			+95	%
Altitude	MIL-STD-810FMethod 500.4
Vibration/Shock	PassMIL-STD-810F -Method 514.5/516.5 – ProcI

4.Mechanical Specifications
Parameter	Value	Unit
Dimension	200 x158x 25	mm
Weight	1.4	kg
RF ConnectorsIn/Out	Input: SMA-FOutput:N-F	-
Control Connector	D-Sub15-PinFemale	-
Power Supply Connector	Pull-core Capacitance	-
Cooling	ExternalHeat sink	-

5.DC Interface Connector
PIN#	Description	Specification
GroundingPost	GND	GroundReturn
Pull-core Capacitance	VDD	Supply Voltage:+24V~32V,+28VNominal
1	RS485(-) [note1][note2]	Serial CommunicationBus
2	TemperatureReporting	Analog Output Voltage @10mV/°C with a 500mVoffset(i.e. 0.75V= 25°C)
3	Address1 (Reserved)	Hardware Address1
4	Address 3(Reserved)	Hardware Address 3
5	Attenuatorsetting [note1]	Voltageinput in the range of0.5-3.0VDC,0.5VDCcorresponds with minimum attenuation, 3.0VDCismaximum attenuation.
6	PAEnable	0/3.3V logiclevels: Power Amplifier disable is a TTLLogicLow (0V).(Internally Pulled-High 3.3V)
7	Alarm	Amplifier Alarmindicator: Normally TTLLow A logicHigh indicates a fault condition, 0/3.3VLogic Levels
8	RS485(+)(Reserved) [note1][note2]	Serial CommunicationBus
9	CurrentReporting	Analog output voltage range of1V/10A (i.e.1.5V=15A)
10	Address 0(Reserved)	Hardware Address 0 –Least significant bit
11	Address 2(Reserved)	Hardware Address 2
12	Address 4 (Reserved)	Hardware Address 4 –Most significant bit
13	NotUsed	No Connection
14	NotUsed	No Connection
15	Reset	Hardwarereset Logic 0V to resetPAandclearlatched faults

Zhuhai Dewin Communication Technology Co., Ltd is established in 2018. It is a leading provider of RF microwave power ampli-fer. drone jammer.drone detector, and other RF components. Our products incorporate LDMOS,GaN.LORA andDigital VCO technology.which are designed to meet the diverse needs of our clients. The products we offer cover a frequencyrange of 100-18000MHz,with power levels ranging from 10W to 200W,with the operating temperature range of -40 °C ~+85°C. Each module we provide has undergone aging testing. meanwhile our modules are characterized by their small size, highefficiency,good stability, and excellent consistency.

We can offer very competitive prices and high-quality services.With a strong focus on innovation and quality.we have earned areputation for delivering reliable and effcient solutions to customers wordwide.We have a professional and experienced R&Dteam,OEM or ODM projects that we can accept.

Our products are widely used in various fields,such as Airport, Public security, National grid.,Oil depot, Mine , Key areadefense.,etc We welcome inquiries from potential customers and partners,and look forward to establishing long-term and mutu-ally beneficial relationships. For more information about our products and services. please visit our website or contact us directy

01 Main business
We are a professional manufacturer and exporter integrating research, development, production andinternational trade.

We own independent factories, advanced production equipment and strict quality control systems.

We provide one-stop services including product design, customized production, quality inspectionand global shipping for worldwide clients.

Domestic sales account for 70% of total revenue, while overseas business takes up 30%. Our keyoverseas markets cover Europe, Southeast Asia and East Asia.

02 Main products
Our main products include anti-drone systems, drone detection systems, RF power amplifier, andantennas.

Our products are widely used in various fields,such as Airport, Public security,National grid.,Oildepot,Mine, Key area defense,etc.

03 Production capacity
We have a total of 3 production lines, 2 assembly lines and 1 debugging and testing line. The monthlyproduction capacity of power amplifier modules is 15,000 pieces. The monthly production of finishedequipment assembly products is 400 units.

Small-batch regular orders are delivered within 3 to 5 days, and batch orders are delivered within 15 days.

04 Quality control
We have professional testing equipment.such as spectrum analyzer,signal analyzer,RF power meter,-network analyzer and ect.

We also have product signal shielding aging chambers,all products are aged for 2 to 3 hours and 100%are tested before being shipped. The quality has received very favorable comments from my clients.

FAQ

Q1: Are you a factory or trading company?
A1: We are a factory ,our factory locates in Jinwan District,Zhuhai,Guag-ndong.Welcome to visit us.

Q2: How about the Shipping Method?
A2: DHL/UPS/TNT/Fedex and other air shipments and sea shipments areall workable. In one words, we could do any shipments you wanted.

Q3: How about the delivery date?
A3: In General, the delivery date will be 5-7 working days for normal buyquantity. But if bigger order, please check us further.

Q4: How about the label and the logo?
A4: Customize label and logo is workable.

Q5: How about the MOQ?
A5: 1 to 20 pcs according to different product.

Q6: How to do if the product i received is defective?
A6: Our strict quality control ensures 100% pass rate. But it can be dam-aged in the way. Please kindly share the defective product photo or video tolet us know where the problem is. We will make the compensation according-ly or send you a part or product.